Air-Source Heat Pump Defrost Cycles: What's Normal and What Isn't
Published:

What a defrost cycle is
A defrost cycle is a short, automatic operation in which your air-source heat pump clears frost or ice from its outdoor unit. If you see a plume of vapour and a bit of meltwater on a cold day, that is usually the heat pump doing its job, not a sign that something has broken.
Why frost forms
The outdoor unit pulls in air and takes heat from it using a coil called the evaporator. To do that, the coil has to run colder than the air passing over it. When the air is cold and damp, moisture freezes onto the coil as a white, frosty coating, much as ice forms in a freezer. Humid air close to freezing makes this more likely.
As the frost thickens, it restricts the airflow through the unit. Less air means less heat collected, so the heat pump has to clear the coil from time to time to keep working properly.
What the cycle does
When the heat pump senses that ice has built up, it runs a defrost cycle on its own. You do not need to start it. In plain terms, the unit stops collecting heat from the air for a short while and uses heat to melt the ice off the outdoor coil instead. That heat can come from the heating system's water or from warming the outdoor fins, depending on the design. Exact methods vary by model and by whether the unit is air-to-water or air-to-air, so your installation manual is the best guide for your own system.
For an air-to-water heat pump, defrosting can draw heat from the heating-water circuit, so enough liquid volume and proper flow rates matter. You do not need to work that out yourself, but it is a fair thing to ask your installer about.
The cycle ends once the coil is clear, and the heat pump returns to normal heating.
What normal defrosting looks and sounds like
Defrosting can look a little dramatic the first time you see it, but the signs are usually ordinary and short-lived.
What you may see
- Steam or vapour. You may see a plume coming from the heat pump. It is steam from the warm, melting coil meeting cold air, not smoke.
- Meltwater. You may notice water coming from the bottom of the unit as the ice melts. This is expected and should drain away.
- Frost clearing. A white coating on the coil that gradually disappears during the cycle is the whole point of defrosting.
If the plume stops and the water runs off once the cycle is over, there is nothing to do.
What you may hear
A brief "whoosh" can occur during a defrost cycle, and any rise in sound levels in winter is usually linked to these temporary cycles, after which normal operation resumes. The fan may also behave differently while the coil is being cleared, so a change in the usual hum is not alarming on its own.
What is not normal is a rattle, a buzz or metallic scraping. Those are not typical defrost noises and are worth having a professional look at.
What you may feel indoors
During defrosting, heat is being used to clear the coil rather than to warm your home, so output can dip for a short time. In a reasonably warm house, most people barely notice it. Defrosting can also slightly increase winter electricity use, which is one small part of why heat pumps use more power in cold weather. Our guide to cold-weather performance covers the wider picture. How often your unit defrosts depends on factors such as how cold and damp the air is, and on how the system was designed and installed, so there is no single number to expect.
Siting, drainage and upkeep
A few simple habits help the unit defrost without trouble:
- Keep the air inlet and outlet free of leaves, vegetation, debris and anything leaning against the unit, so airflow is not blocked.
- Unless your heat pump sits on a soakaway, make sure the condensation drain is clear of obstructions so meltwater can leave the unit.
- Look over the unit for leaks or damaged grilles as part of regular winter checks.
- Do not pour hot water over the heat pump to defrost it.
When defrosting looks unusual
Normal defrosting is brief, clears the ice, and the heat pump goes back to heating. Concern starts when that pattern breaks down.
Signs worth acting on
- Defrost cycles that seem to repeat very often, or that run for noticeably longer than before.
- Ice that stays on the unit or keeps building up rather than clearing.
- A frozen or blocked condensate drain, or meltwater that refreezes around the base.
- Heating that does not recover after a defrost, or a fault message on the display.
- Rattling, buzzing or metallic scraping noises rather than a short whoosh.
None of these proves a fault by itself, because weather and layout matter. But a change from how your unit normally behaves is a good reason to get it checked.
What an engineer may look at
A qualified engineer can assess the cause of excessive frosting and any model-specific fault codes. The checks will depend on the symptoms and the heat pump's design, so treat this as a service question rather than a diagnosis.
What to do next
First, check the simple outdoor causes: is anything blocking the airflow, and is the drain clear? Your user manual will also explain how to reset the heat pump. A reset can sometimes clear a fault or get the unit working again temporarily, but if the problem returns, it still needs attention.
Do not open the casing yourself, as that can be dangerous, and do not pour hot water over the unit. Contact your installer or a qualified service engineer, or the manufacturer's customer service if your unit is under warranty, and tell them:
- how often defrosting happens and how long it lasts,
- whether ice stays on the unit or the drain freezes,
- whether heat comes back afterwards,
- any noises or fault codes you have seen.
If you are still choosing a system, you can use the free Heating Finder calculator to compare heat pump options for your home. Defrosting is a normal part of winter running, so it is worth discussing with installers before you decide.


